Thuren Control Arms are a great addition to any solid axle Dodge Ram! These arms are much stronger than the OEM arms, and have more clearance for turning bigger tires.
Unlike OEM, our bushings have a good amount of deflection, and are not prone to failure with increased suspension travel.
Fitment:
- Works on trucks with 0" to 3.5" of lift
Details:
- Arms are 1/2" longer length, allowing the use of 37" tires, even with wheel offsets close to factory specs
- Lower arms are built from high strength 1.5"x3/8" wall 1026 DOM tube
- Upper arms are a solid alloy bar
- Wide flange joints, to make sure bolt torque has no problem keeping the arms locked in place, even under heavy abuse
- Bend in lower arms do not cross center to retain impact strength.
- Machined in house proprietary Self Centering joints to prevent the arms from rocking to one side and rubbing the frame/axle.
- 17-4 Stainless Steel center pivots. 17-4 Stainless is about as hard as a Grade 8 bolt, so these joints will not crush like other brand arms.
- Stainless steel center pivots prevent rust seizing of the bolts and make for easy removal.
- Joints are easy to grease and maintain. No special tools are required it is a very easy and inexpensive job to rebuild.
- Arms are texture blasted before powder-coating, to prevent impact chipping of the coating.
- Main joint bushings are a moderate durometer high quality PTMEG Polyurethane for great wear resistance, and great vibration control.
We often get people that insist they need adjustable control arms. About the only time this is true, is if you are trying to build a custom 4" or so lift, or if you want to run this style arm (short arms) on taller 4" to 6" lifts or so. Problem with both of these scenarios is explained below:
- With 0-3" of lift, you can only make the control arms 1/2" longer than stock. If you make them ANY longer, even 1/8", you will most likely hit the coil mount on the axle against the frame when the suspension cycles. Our arms are already the longest they can be with 0-3" of lift.
- With over 4" of lift, short arms degrade handling and ride quality a MASSIVE amount. Instead of investing in expensive adjustable short arms, put that money into purchasing long arms, and build the truck the proper way.
- Lifts between the 4" and 6" height requires all the same drop components. This means that with a 4" lift you have to limit bump travel 3". This means you increase your bump travel 1" more than stock. Massive waste of potential. For reference, our 3" lifts do not restrict bump travel, so you increase bump travel the full 3" when you lift 3".
Thuren Control Arms are a great addition to any solid axle Dodge Ram! These arms are much stronger than the OEM arms, and have more clearance for turning bigger tires.
Unlike OEM, our bushings have a good amount of deflection, and are not prone to failure with increased suspension travel.
Fitment:
- Works on trucks with 0" to 3.5" of lift
Details:
- Arms are 1/2" longer length, allowing the use of 37" tires, even with wheel offsets close to factory specs
- Lower arms are built from high strength 1.5"x3/8" wall 1026 DOM tube
- Upper arms are a solid alloy bar
- Wide flange joints, to make sure bolt torque has no problem keeping the arms locked in place, even under heavy abuse
- Bend in lower arms do not cross center to retain impact strength.
- Machined in house proprietary Self Centering joints to prevent the arms from rocking to one side and rubbing the frame/axle.
- 17-4 Stainless Steel center pivots. 17-4 Stainless is about as hard as a Grade 8 bolt, so these joints will not crush like other brand arms.
- Stainless steel center pivots prevent rust seizing of the bolts and make for easy removal.
- Joints are easy to grease and maintain. No special tools are required it is a very easy and inexpensive job to rebuild.
- Arms are texture blasted before powder-coating, to prevent impact chipping of the coating.
- Main joint bushings are a moderate durometer high quality PTMEG Polyurethane for great wear resistance, and great vibration control.
We often get people that insist they need adjustable control arms. About the only time this is true, is if you are trying to build a custom 4" or so lift, or if you want to run this style arm (short arms) on taller 4" to 6" lifts or so. Problem with both of these scenarios is explained below:
- With 0-3" of lift, you can only make the control arms 1/2" longer than stock. If you make them ANY longer, even 1/8", you will most likely hit the coil mount on the axle against the frame when the suspension cycles. Our arms are already the longest they can be with 0-3" of lift.
- With over 4" of lift, short arms degrade handling and ride quality a MASSIVE amount. Instead of investing in expensive adjustable short arms, put that money into purchasing long arms, and build the truck the proper way.
- Lifts between the 4" and 6" height requires all the same drop components. This means that with a 4" lift you have to limit bump travel 3". This means you increase your bump travel 1" more than stock. Massive waste of potential. For reference, our 3" lifts do not restrict bump travel, so you increase bump travel the full 3" when you lift 3".
